SAFETY AND INSTALLATION INSTRUCTIONS Model - Farnell

Loading...

SAFETY AND INSTALLATION INSTRUCTIONS Model: FL124BPIR 24W Low Energy Floodlight with PIR IMPORTANT! Please read these instructions before installing your new fitting. Please retain for future reference.

Pack Contents

Floodlight 24W Compact Fluorescent Lamp

x1 x1

General Information, Safety and Installation Instructions Introduction

The chosen location of your new fitting should allow for the product to be securely mounted and safely connected to the mains supply (lighting circuit).

Your new floodlight incorporates a PIR (Passive Infra Red) sensing device which is sensitive to movement of warm objects within a preset operating zone and immediately switches the light on when movement is detected.

When choosing the location for your new fitting, ensure that the fixings will be anchored in a solid surface e.g. concrete, brick or a joist—do not fix directly onto panelling, cladding, plasterboard etc.

This makes this fitting ideal for automatically illuminating pathways, steps, patios, porches, or whatever area you have selected to light for reasons of safety, convenience or security. While there is movement within range of the unit the light will remain on.

If the location of your new fitting requires the provision of a new electrical supply, the supply must conform with the requirements of the Building Regulations making reference to the current edition of the IEE Wiring Regulations (BS7671). This product is designed for permanent connection to fixed wiring: this should be either a suitable lighting circuit (protected with a 5 or 6 Amp MCB or fuse) or a fused spur (with a 3 Amp fuse) via a fused connection unit.

Read this first Check the pack and make sure you have all of the parts listed on the front of this booklet. If not, contact the outlet where you bought this product.

We recommend that the supply incorporates a switch for ease of operation.

This product contains glass, care must be taken when assembling, fitting or handling to prevent personal injury or damage to the product.

Make connections to the electrical supply in accordance with the following code: Live - Brown or Red Neutral - Blue or Black Earth - Green and Yellow

This light fitting must be installed by a competent person in accordance with the Building Regulations making reference to the current edition of the IEE Wiring Regulations (BS7671). The Building Regulations may be obtained from HMSO or viewed and downloaded from www.communities.gov.uk following the link for Building Regulations.

When making connections, ensure that the terminals are tightened securely and that no strands of wire protrude. Check that the terminals are tightened onto the bared conductors and not onto any insulation.

As the buyer, installer and/or user of this product it is your own responsibility to ensure that this fitting is fit for the purpose for which you have intended it. Eterna Lighting cannot accept any liability for loss, damage or premature failure resulting from inappropriate use.

This product must be connected to Earth. IMPORTANT - Always switch off at the mains before changing the lamp. Do not mount on a surface that is likely to vibrate.

If in any doubt, consult a qualified electrician. TIME SENS

For maximum detection area, the light should be mounted 1.8 to 2.5 meters (6 to 8ft) above the �������������� ������������� detection area (refer Fig.1A). The floodlight scanning specifications (approximately 12 meters at 180°) may vary slightly depending on the mounting height and location.

LUX

The lamps (bulbs/tubes) supplied with this fitting are consumable parts and therefore may be outside of any warranty offered. Switch off the mains before commencing installation ������������������� and remove the appropriate circuit fuse. When working at heights, please use a suitable platform. Disconnect the fitting from the electrical supply before flash or high voltage testing. Suitable for indoor and outdoor use.

Issue 090714-1PA

This product is suitable for installation on surfaces with normal flammability e.g. wood, plasterboard, and masonry. It is not suitable for use on highly flammable surfaces (e.g. polystyrene, textiles).

�������

���� ��������� ������

Before making fixing hole(s), check that there are no obstructions hidden beneath the mounting surface such as pipes or cables.

��

��

���

������������������������ 2

Installation Instructions and Care of the washers, it is important to fit them in the correct order (see Fig. 2)

The detection range of the unit may alter with changes in ambient temperature. To avoid damage to the PIR unit, do not aim the sensor towards the sun.

3.

To avoid nuisance triggering, the sensor should be directed away from heat sources such as barbecues, air-conditioners, other outside lighting, moving cars and flue vents.

Using the fixing strap as a template, mark the position for the fixing holes on your mounting surface.

4. Prepare your mounting surface as appropriate for your chosen fixings (not supplied). Use a spirit level to ensure the fitting will be level.

Do not connect to circuits with other light fittings or appliances such as large fans, washing machines, fluorescent lights etc. that may cause false triggering through spikes generated in the mains supply.

Do not aim towards reflective surfaces such as smooth white walls, swimming pools, etc. Before selecting a place to install your floodlight you should note that movement across the scan area is more effective than movement directly towards or away from the sensor (refer Fig.1B). When walking directly towards or away from the sensor rather than across, the apparent detection range will be substantially reduced (refer Fig. 1C).

5.

Secure the strap in place.

6.

Fit the floodlight back onto the fixing strap and replace the screws.

7.

Before tightening the screws at the ends of the fixing strap, adjust the position of the floodlight to give the desired area of illumination.

8.

Tighten the screws to lock your floodlight in position.

9.

Undo the four screws in the connection box cover and remove it, take care not to lose any of the screws or the sealing gasket.

10. Undo the screws and lift off the cable clamp. 11. Undo and remove the cable entry nut and gland. 12. If necessary, pierce the gland making a hole just large enough for your supply cable to pass through so that the gland makes a tight seal around it. 13. Thread your supply cable through the nut and gland and into the connection box.

��������������

14. Make the connections to your mains supply as described in the “Read this first” section.

�������������

Do not attempt to modify the light or PIR sensor unit, there are no user serviceable parts inside.

15. Replace the cable grip and connection box cover ensuring that the cable is held securely and the gasket is correctly positioned.

You are advised at every stage of your installation to double-check any electrical connections you have made. After you have completed your installation there are electrical tests that should be carried out: these tests are specified in the Wiring Regulations (BS7671) referred to in the Building Regulations. If in doubt, consult a qualified electrician.

Installation

16. Using a cross-headed screwdriver, undo the screws that secure the diffuser and allow to hang down. 17. Fit the fluorescent lamp by pressing straight into the lampholder. 18. Replace the diffuser and tighten the screws making sure that the waterproof gasket is correctly positioned and compressed.

�������

����

1.

Choose the location for your new floodlight giving ��������� consideration to all of the conditions listed above.

2.

Loosen the screws at each end of the fixing �� the position �� it. Note ���of each bracket and remove

������

������������������������

19. Restore the power and switch on.

3

Installation Instructions & Care

����������������

Fig. 2

�����������

�����������������

�������������� �����������

��������������������������

�������������������������

Understanding the Controls (Refer to the Fig.3)

1.

� �

������������� ��������������

������������������ �������������������

���������������� ������������������������ ����������������� ��������������� ����������������

Direct the sensor toward the desired area to be scanned by adjusting the swivel joint on the sensor arm. Important: loosen the lock nuts and screws on sensor and floodlight before making any adjustments.

TIME SENS

LUX

2.

Have another person move across the centre of the

area to be scanned and slowly adjust the angle of �������������� �������������

the sensor arm until the unit sensors the presence of the moving person, causing the floodlight to switch on (refer Fig. 1B).

������������������� 3.

Adjust time control to required setting.

4. To set the light level at which the floodlight will automatically switch “on” at night, turn the LUX Adjusting the duration time: The length of time that control knob from daylight ( ) to night ( ). If the the light remains switched on after activation can floodlight is required to switch on earlier, e.g. dusk, be adjusted from (10±5) seconds to (4±1) minutes. wait for the desired light level, then slowly turn the Rotating the TIME knob anti-clockwise will reduce the LUX control knob ������� towards daylight while someone duration time. Note: Once the light has been triggered ���� of the area to be detected. walks across the centre by the PIR sensor any subsequent detection will start the When the floodlight switches on, release the ��������� timed period again from the beginning. ������LUX control knob. You may need to make further adjustments to achieve your ideal light level setting �� �� ��� Adjusting the lux control level: The Lux control module has a built-in sensing device (photocell) that detects Specifications daylight and darkness. Rotating the LUX knob clockwise ������������������������ is from light ( ) to dark ( ). The ( ) position denotes Detection Range: Max. 12 meters at approx. 180° scan that the Floodlights can work at day and night and the (see notes above) ( ) position only work at night. You can set to operate Duration Time Adjustment: (10±5) secs to (4±1) mins the unit at the desired level by adjusting the LUX knob. Detection Circuitry: Passive Infra-Red (PIR) 4W Consumption (sensor head only) Weatherproof: IP44 Adjusting the sensitivity: The sensitivity means the Power Required: 220-240V~ 50 Hz maximum distance at which PIR sensor can be triggered. Maximum Load: E27;1x24W CFL Energy saving lamp Turning the SENS knob anti-clockwise will decrease the Recommended power supply cable: H05RN-F 3G sensitivity 1.0mm2 Protection: Class I Setting the controls: Turn the Lux control knob to light Unit Dimension: 222(L) x 133(W) x 234(H) mm ( ) position, turn the wall switch on and wait half a minute for the control circuit to stabilize. At this stage ensure that the TIME control knob is set at minimum Safety Markings duration time (-) position (Rotating the TIME knob anticlockwise to stop-position). The floodlight will now IP44 switch on and remain on for about 30 seconds (within 60 seconds). 4

Installation Instructions & Care Cleaning To avoid dust build-up and ensure proper functioning of the floodlight, please wipe the sensor lens lightly with a damp cloth every 3 months.

3.

Remove the lamp. Pull directly out of lampholder, do not twist.

4.

Insert new lamp.

5.

Replace the diffuser and secure in position making sure that the gasket is correctly positioned and compressed.

6.

Restore the power and switch on.

Disconnect the power and clean the exterior only of this fitting with a moist (not wet) cloth. Do not use any chemical or abrasive cleaners.

Replacement Lamp Type

Lamp Replacement

Wattage: 24W Type: 24W ES Helical CFLi

1.

Switch off the electricity at the mains.

2.

Using a cross-headed screwdriver, loosen the screws and lift off the diffuser.

This fitting is designed for low energy compact fluorescent lamps, do not use incandescent or halogen lamps.

Trouble Shooting & User Hints Problem

Possible Cause

Suggested Solutions

Light does not switch on when there is movement in the detection area

1. No mains voltage 2. Bulb - faulty/missing 3. Light nearby is too bright 4. Controls set incorrectly 5. Sensor postioned in wrong direction

• Check all connections, fuses and switches • Check. Replace • Redirect sensor or relocate the unit • Readjust sensor angle or control knob • Redirect sensor and/or adjust

Lamp switches on for no apparent reason (false trigger)

1. Heat from lamp body activating sensor

• Adjust PIR sensor or floodlight to allow a minimum gap 40mm between floodlight body and sensor head

2. Heat sources i.e; air-con, vents, heater flues, bbq’s, outside light, moving cars can activate sensor

• Adjust direction of sensor head away from these sources

3. Animals or birds e.g. possums or domestic animals

• Redirecting sensor may help

4. Interference from on/off switching of electric fans, lights on the same circuit as your security floodlight. (This problem does not always occur but a faulty switch or noisy fluorescent light may cause the security floodlight to switch on

• Should the false triggering become, troublesome, consider: (a) Replacing a faulty switch. (b) Replacing noisy fluorescent tubes/starters (c) Connecting the floodlight to a separate circuit (in most cases where one or more of the above suggestions have been carried out, false triggering has been reduced)

5. Reflection from swimming pool or reflective surface

• Relocate the fitting

Light remains on

1. Continuously false triggered 2. Time to set too long

• Redirecting sensor head may help • Reduce time

Light switches on during daylight hours

1. LUX control knob is set to daylight position

• Turn the LUX control knob to desired light level setting

When setting lux controls in daylight the detection distance becomes shorter

1. Interference by sunlight

• Re-test at night

Note: All passive infra red detectors are more sensitive in cold and dry weather than warm and wet weather. 5

Eventually, you may want to replace this light fitting When your light fitting comes to the end of its life or you choose to update or upgrade it by replacing it, please do not dispose of it with your normal household waste, please recycle where facilities exist. When you need to dispose of this fitting, check with your retailer or local authority for suitable options. New regulations require the recycling of Waste from Electrical and Electronic Equipment (European “WEEE Directive” effective August 2005—UK WEEE Regulations effective 2nd January 2007). Environment Agency Registered Producer: WEE/GA0248QZ

If your light is defective or develops a fault, please return it to the place where you bought it. You can call our Helpline for advice. The Helpline will gladly give advice on any aspect of any Eterna Lighting product but may not be able to give specific instructions regarding individual installations. If in doubt, consult a qualified electrician.

Help Line Tel: 01933 673 144 Fax: 01933 678 083 Email: [email protected] For all other information visit our website www.eterna-lighting.co.uk

Loading...

SAFETY AND INSTALLATION INSTRUCTIONS Model - Farnell

SAFETY AND INSTALLATION INSTRUCTIONS Model: FL124BPIR 24W Low Energy Floodlight with PIR IMPORTANT! Please read these instructions before installing y...

358KB Sizes 6 Downloads 13 Views

Recommend Documents

INSTALLATION INSTRUCTIONS ) INSTRUCTIONS D'INSTALLATION
de desagüe. Extensión para manguera de desagüe de 1,2 m (4 pies), pieza número DRNEXT4. Llave de extremo abierto o l

INSTALLATION INSTRUCTIONS
specified in Lennox Engineering Handbook. Coils previously charged with ..... Use this method if the existing outdoor un

Installation Instructions
Regulations may require that the material be tested to determine asbestos content and may govern the removal and disposa

INSTALLATION INSTRUCTIONS
Operação teste da unidade de ar condicionado. Leitourgiva kai dokimhvtou klimatistikouv. Measuring pressure and gas ch

INSTALLATION INSTRUCTIONS
Item 10 - 26 - Remote Sensor. ART-K45AGB. System Controller. SHA-KC64AGB. Schedule Timer. SHA-TM64AGB. DC_Inverter_Eng.i

INSTALLATION INSTRUCTIONS
system configuration, the Net Positive Suction Head (NPSH) available (Hatmosphere + Hvapour + Hstatic +. Hpoint losses +

INSTALLATION INSTRUCTIONS
Pump Curves is the specs that you will receive from your supplier. System Curves can only be determined after you have d

Safety Signs Selection Guide - Farnell
Safety signs are a necessary and required component for warning and communicating messages or notices to your employees,

INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION
This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system fo

Pump Installation and Operation Instructions
This package contains a single spreadsheet named 'pumptest.xls' which should be saved on your local hard disk. The sprea